# SPDX-License-Identifier: GPL-2.0-only
menuconfig POWER_SUPPLY
bool "Power supply class support"
help
Say Y here to enable power supply class support. This allows
power supply (batteries, AC, USB) monitoring by userspace
via sysfs and uevent (if available) and/or APM kernel interface
(if selected below).
if POWER_SUPPLY
config POWER_SUPPLY_DEBUG
bool "Power supply debug"
help
Say Y here to enable debugging messages for power supply class
and drivers.
config POWER_SUPPLY_HWMON
bool
prompt "Expose power supply sensors as hwmon device"
depends on HWMON=y || HWMON=POWER_SUPPLY
default y
help
This options enables API that allows sensors found on a
power supply device (current, voltage, temperature) to be
exposed as a hwmon device.
Say 'Y' here if you want power supplies to
have hwmon sysfs interface too.
config APM_POWER
tristate "APM emulation for class batteries"
depends on APM_EMULATION
help
Say Y here to enable support APM status emulation using
battery class devices.
config ADC_BATTERY_HELPER
tristate
config GENERIC_ADC_BATTERY
tristate "Generic battery support using IIO"
depends on IIO
help
Say Y here to enable support for the generic battery driver
which uses IIO framework to read adc.
config IP5XXX_POWER
tristate "Injoinic IP5xxx power bank IC driver"
depends on I2C
select REGMAP_I2C
help
Say Y to include support for Injoinic IP5xxx power bank ICs,
which include a battery charger and a boost converter.
config MAX8925_POWER
tristate "MAX8925 battery charger support"
depends on MFD_MAX8925
help
Say Y here to enable support for the battery charger in the Maxim
MAX8925 PMIC.
config WM831X_BACKUP
tristate "WM831X backup battery charger support"
depends on MFD_WM831X
help
Say Y here to enable support for the backup battery charger
in the Wolfson Microelectronics WM831x PMICs.
config WM831X_POWER
tristate "WM831X PMU support"
depends on MFD_WM831X
help
Say Y here to enable support for the power management unit
provided by Wolfson Microelectronics WM831x PMICs.
config WM8350_POWER
tristate "WM8350 PMU support"
depends on MFD_WM8350
help
Say Y here to enable support for the power management unit
provided by the Wolfson Microelectronics WM8350 PMIC.
config TEST_POWER
tristate "Test power driver"
help
This driver is used for testing. It's safe to say M here.
config BATTERY_88PM860X
tristate "Marvell 88PM860x battery driver"
depends on MFD_88PM860X
help
Say Y here to enable battery monitor for Marvell 88PM860x chip.
config CHARGER_ADP5061
tristate "ADP5061 battery charger driver"
depends on I2C
select REGMAP_I2C
help
Say Y here to enable support for the ADP5061 standalone battery
charger.
This driver can be built as a module. If so, the module will be
called adp5061.
config BATTERY_ACT8945A
tristate "Active-semi ACT8945A charger driver"
depends on MFD_ACT8945A || COMPILE_TEST
help
Say Y here to enable support for power supply provided by
Active-semi ActivePath ACT8945A charger.
config BATTERY_CHAGALL
tristate "Pegatron Chagall battery driver"
depends on I2C
depends on LEDS_CLASS
help
Say Y to include support for Cypress CG7153AM IC based battery
fuel gauge with custom firmware found in Pegatron Chagall based
tablet line.
This driver can also be built as a module. If so, the module will be
called chagall-battery.
config BATTERY_CPCAP
tristate "Motorola CPCAP PMIC battery driver"
depends on MFD_CPCAP && IIO
default MFD_CPCAP
help
Say Y here to enable support for battery on Motorola
phones and tablets such as droid 4.
config BATTERY_CW2015
tristate "CW2015 Battery driver"
depends on I2C
select REGMAP_I2C
help
Say Y here to enable support for the cellwise cw2015
battery fuel gauge (used in the Pinebook Pro & others)
This driver can also be built as a module. If so, the module will be
called cw2015_battery.
config BATTERY_DS2760
tristate "DS2760 battery driver (HP iPAQ & others)"
depends on W1
help
Say Y here to enable support for batteries with ds2760 chip.
config BATTERY_DS2780
tristate "DS2780 battery driver"
depends on HAS_IOMEM
select W1
select W1_SLAVE_DS2780
help
Say Y here to enable support for batteries with ds2780 chip.
config BATTERY_DS2781
tristate "DS2781 battery driver"
depends on HAS_IOMEM
select W1
select W1_SLAVE_DS2781
help
If you enable this you will have the DS2781 battery driver support.
The battery monitor chip is used in many batteries/devices
as the one who is responsible for charging/discharging/monitoring
Li+ batteries.
If you are unsure, say N.
config BATTERY_DS2782
tristate "DS2782/DS2786 standalone gas-gauge"
depends on I2C
help
Say Y here to enable support for the DS2782/DS2786 standalone battery
gas-gauge.
config BATTERY_HUAWEI_GAOKUN
tristate "Huawei Matebook E Go power supply"
depends on EC_HUAWEI_GAOKUN
help
This driver enables battery and adapter support on the Huawei Matebook
E Go, which is a sc8280xp-based 2-in-1 tablet.
To compile the driver as a module, choose M here: the module will be
called huawei-gaokun-battery.
config BATTERY_LEGO_EV3
tristate "LEGO MINDSTORMS EV3 battery"
depends on OF && IIO && GPIOLIB && (ARCH_DAVINCI_DA850 || COMPILE_TEST)
help
Say Y here to enable support for the LEGO MINDSTORMS EV3 battery.
config BATTERY_LENOVO_YOGA_C630
tristate "Lenovo Yoga C630 battery"
depends on EC_LENOVO_YOGA_C630
help
This driver enables battery support on the Lenovo Yoga C630 laptop.
To compile the driver as a module, choose M here: the module will be
called lenovo_yoga_c630_battery.
config BATTERY_PMU
tristate "Apple PMU battery"
depends on PPC32 && ADB_PMU
help
Say Y here to expose battery information on Apple machines
through the generic battery class.
config BATTERY_QCOM_BATTMGR
tristate "Qualcomm PMIC GLINK battery manager support"
depends on QCOM_PMIC_GLINK
select AUXILIARY_BUS
help
Say Y here to enable the Qualcomm PMIC GLINK power supply driver,
which is used on modern Qualcomm platforms to provide battery and
power supply information.
config BATTERY_OLPC
tristate "One Laptop Per Child battery"
depends on OLPC_EC
help
Say Y to enable support for the battery on the OLPC laptop.
config BATTERY_SAMSUNG_SDI
bool "Samsung SDI batteries"
help
Say Y to enable support for Samsung SDI battery data.
These batteries are used in Samsung mobile phones.
config BATTERY_S2MU005
tristate "Samsung S2MU005 PMIC fuel gauge driver"
depends on I2C
select REGMAP_I2C
help
Say Y to enable support for the Samsung S2MU005 PMIC integrated
fuel gauge, which works indepenently of the PMIC battery charger
counterpart, and reports battery metrics.
This driver, if built as a module, will be called s2mu005-fuel-gauge.
config BATTERY_COLLIE
tristate "Sharp SL-5500 (collie) battery"
depends on SA1100_COLLIE && MCP_UCB1200
help
Say Y to enable support for the battery on the Sharp Zaurus
SL-5500 (collie) models.
config BATTERY_INGENIC
tristate "Ingenic JZ47xx SoCs battery driver"
depends on MIPS || COMPILE_TEST
depends on INGENIC_ADC
help
Choose this option if you want to monitor battery status on
Ingenic JZ47xx SoC based devices.
This driver can also be built as a module. If so, the module will be
called ingenic-battery.
config BATTERY_INTEL_DC_TI
tristate "Intel Bay / Cherry Trail Dollar Cove TI battery driver"
depends on INTEL_SOC_PMIC_CHTDC_TI && INTEL_DC_TI_ADC && IIO && ACPI
select ADC_BATTERY_HELPER
help
Choose this option if you want to monitor battery status on Intel
Bay Trail / Cherry Trail tablets using the Dollar Cove TI PMIC's
coulomb-counter as fuel-gauge.
To compile this driver as a module, choose M here: the module will be
called intel_dc_ti_battery.
config BATTERY_IPAQ_MICRO
tristate "iPAQ Atmel Micro ASIC battery driver"
depends on MFD_IPAQ_MICRO
help
Choose this option if you want to monitor battery status on
Compaq/HP iPAQ h3100 and h3600.
config BATTERY_WM97XX
bool "WM97xx generic battery driver"
depends on TOUCHSCREEN_WM97XX=y
help
Say Y to enable support for battery measured by WM97xx aux port.
config BATTERY_SBS
tristate "SBS Compliant gas gauge"
depends on I2C
help
Say Y to include support for SBS battery driver for SBS-compliant
gas gauges.
config CHARGER_SBS
tristate "SBS Compliant charger"
depends on I2C
select REGMAP_I2C
help
Say Y to include support for SBS compliant battery chargers.
config MANAGER_SBS
tristate "Smart Battery System Manager"
depends on I2C && I2C_MUX && GPIOLIB
select I2C_SMBUS
help
Say Y here to include support for Smart Battery System Manager
ICs. The driver reports online and charging status via sysfs.
It presents itself also as I2C mux which allows to bind
smart battery driver to its ports.
Supported is for example LTC1760.
This driver can also be built as a module. If so, the module will be
called sbs-manager.
config BATTERY_BQ27XXX
tristate "BQ27xxx battery driver"
help
Say Y here to enable support for batteries with BQ27xxx chips.
config BATTERY_BQ27XXX_I2C
tristate "BQ27xxx I2C support"
depends on BATTERY_BQ27XXX
depends on I2C
default y
help
Say Y here to enable support for batteries with BQ27xxx chips
connected over an I2C bus.
config BATTERY_BQ27XXX_HDQ
tristate "BQ27xxx HDQ support"
depends on BATTERY_BQ27XXX
depends on W1
default y
help
Say Y here to enable support for batteries with BQ27xxx chips
connected over an HDQ bus.
config BATTERY_BQ27XXX_DT_UPDATES_NVM
bool "BQ27xxx support for update of NVM/flash data memory"
depends on BATTERY_BQ27XXX_I2C
help
Say Y here to enable devicetree monitored-battery config to update
NVM/flash data memory. Only enable this option for devices with a
fuel gauge mounted on the circuit board, and a battery that cannot
easily be replaced with one of a different type. Not for
general-purpose kernels, as this can cause misconfiguration of a
smart battery with embedded NVM/flash.
config BATTERY_DA9030
tristate "DA9030 battery driver"
depends on PMIC_DA903X
help
Say Y here to enable support for batteries charger integrated into
DA9030 PMIC.
config BATTERY_DA9052
tristate "Dialog DA9052 Battery"
depends on PMIC_DA9052
help
Say Y here to enable support for batteries charger integrated into
DA9052 PMIC.
config CHARGER_DA9150
tristate "Dialog Semiconductor DA9150 Charger support"
depends on MFD_DA9150
depends on DA9150_GPADC
depends on IIO
help
Say Y here to enable support for charger unit of the DA9150
Integrated Charger & Fuel-Gauge IC.
This driver can also be built as a module. If so, the module will be
called da9150-charger.
config BATTERY_DA9150
tristate "Dialog Semiconductor DA9150 Fuel Gauge support"
depends on MFD_DA9150
help
Say Y here to enable support for the Fuel-Gauge unit of the DA9150
Integrated Charger & Fuel-Gauge IC
This driver can also be built as a module. If so, the module will be
called da9150-fg.
config CHARGER_AXP20X
tristate "X-Powers AXP20X and AXP22X AC power supply driver"
depends on MFD_AXP20X
depends on AXP20X_ADC
depends on IIO
help
Say Y here to enable support for X-Powers AXP20X and AXP22X PMICs' AC
power supply.
This driver can also be built as a module. If so, the module will be
called axp20x_ac_power.
config BATTERY_AXP20X
tristate "X-Powers AXP20X battery driver"
depends on MFD_AXP20X
depends on AXP20X_ADC
depends on IIO
help
Say Y here to enable support for X-Powers AXP20X PMICs' battery power
supply.
This driver can also be built as a module. If so, the module will be
called axp20x_battery.
config AXP20X_POWER
tristate "AXP20x power supply driver"
depends on MFD_AXP20X
depends on IIO
help
This driver provides support for the power supply features of
AXP20x PMIC.
config AXP288_CHARGER
tristate "X-Powers AXP288 Charger"
depends on MFD_AXP20X && EXTCON_AXP288 && IOSF_MBI && ACPI
help
Say yes here to have support X-Power AXP288 power management IC (PMIC)
integrated charger.
config AXP288_FUEL_GAUGE
tristate "X-Powers AXP288 Fuel Gauge"
depends on MFD_AXP20X && IIO && IOSF_MBI && ACPI
help
Say yes here to have support for X-Power power management IC (PMIC)
Fuel Gauge. The device provides battery statistics and status
monitoring as well as alerts for battery over/under voltage and
over/under temperature.
config BATTERY_MAX17040
tristate "Maxim MAX17040/17041/17043 family Fuel Gauge"
depends on I2C && IIO
select REGMAP_I2C
help
Driver supports Maxim fuel-gauge systems for lithium-ion (Li+)
batteries used mainly in handheld and portable equipment.
Supported devices: max17040, max17041, max17043, max17044, max17048,
max17049, max17058, max17059, max77836.
Driver supports reporting SOC (State of Charge, i.e capacity),
voltage and configurable low-SOC wakeup interrupt.
Driver can be build as a module (max17040_battery).
config BATTERY_MAX17042
tristate "Maxim MAX17042/17047/17050/8997/8966 family Fuel Gauge"
depends on I2C
select REGMAP_I2C
help
MAX17042 is fuel-gauge systems for lithium-ion (Li+) batteries
in handheld and portable equipment. The MAX17042 is configured
to operate with a single lithium cell. MAX8997 and MAX8966 are
multi-function devices that include fuel gauages that are compatible
with MAX17042.
Supported devices: max8966, max8997, max17042, max17047, max17050,
max17055, max77693, max77849.
Driver can be build as a module (max17042_battery).
config BATTERY_MAX1720X
tristate "Maxim MAX17201/MAX17205 Fuel Gauge"
depends on I2C
select REGMAP_I2C
help
MAX1720x is a family of fuel-gauge systems for lithium-ion (Li+)
batteries in handheld and portable equipment. MAX17201 are
configured to operate with a single lithium cell, the MAX17205
can operate with multiple cells.
Say Y to include support for the MAX17201/MAX17205 Fuel Gauges.
config BATTERY_MAX1721X
tristate "MAX17211/MAX17215 standalone gas-gauge"
depends on W1
select REGMAP_W1
help
MAX1721x is fuel-gauge systems for lithium-ion (Li+) batteries
in handheld and portable equipment. MAX17211 used with single cell
battery. MAX17215 designed for muticell battery. Both them have
OneWire (W1) host interface.
Say Y here to enable support for the MAX17211/MAX17215 standalone
battery gas-gauge.
config BATTERY_TWL4030_MADC
tristate "TWL4030 MADC battery driver"
depends on TWL4030_MADC
help
Say Y here to enable this dumb driver for batteries managed
through the TWL4030 MADC.
config CHARGER_88PM860X
tristate "Marvell 88PM860x Charger driver"
depends on MFD_88PM860X && BATTERY_88PM860X
help
Say Y here to enable charger for Marvell 88PM860x chip.
config CHARGER_PF1550
tristate "NXP PF1550 battery charger driver"
depends on MFD_PF1550
help
Say Y to enable support for the NXP PF1550 battery charger.
The device is a single cell Li-Ion/Li-Polymer battery charger for
portable application.
This driver can also be built as a module. If so, the module will be
called pf1550-charger.
config BATTERY_RX51
tristate "Nokia RX-51 (N900) battery driver"
depends on TWL4030_MADC
help
Say Y here to enable support for battery information on Nokia
RX-51, also known as N900 tablet.
config CHARGER_CPCAP
tristate "CPCAP PMIC Charger Driver"
depends on MFD_CPCAP && IIO
depends on OMAP_USB2 || (!OMAP_USB2 && COMPILE_TEST)
default MFD_CPCAP
help
Say Y to enable support for CPCAP PMIC charger driver for Motorola
mobile devices such as Droid 4.
config CHARGER_ISP1704
tristate "ISP1704 USB Charger Detection"
depends on USB_PHY
depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y'
help
Say Y to enable support for USB Charger Detection with
ISP1707/ISP1704 USB transceivers.
config CHARGER_MAX8903
tristate "MAX8903 Battery DC-DC Charger for USB and Adapter Power"
help
Say Y to enable support for the MAX8903 DC-DC charger and sysfs.
The driver supports controlling charger-enable and current-limit
pins based on the status of charger connections with interrupt
handlers.
config CHARGER_TWL4030
tristate "OMAP TWL4030 BCI charger driver"
depends on IIO && TWL4030_CORE
help
Say Y here to enable support for TWL4030 Battery Charge Interface.
config CHARGER_TWL6030
tristate "OMAP TWL6030 BCI charger driver"
depends on IIO && TWL4030_CORE
help
Say Y here to enable support for TWL6030/6032 Battery Charge
Interface.
This driver can be build as a module. If so, the module will be
called twl6030_charger.
config CHARGER_LP8727
tristate "TI/National Semiconductor LP8727 charger driver"
depends on I2C
help
Say Y here to enable support for LP8727 Charger Driver.
config CHARGER_LP8788
tristate "TI LP8788 charger driver"
depends on MFD_LP8788
depends on LP8788_ADC
depends on IIO
help
Say Y to enable support for the LP8788 linear charger.
config CHARGER_GPIO
tristate "GPIO charger"
depends on GPIOLIB || COMPILE_TEST
help
Say Y to include support for chargers which report their online status
through a GPIO pin.
This driver can be build as a module. If so, the module will be
called gpio-charger.
config CHARGER_MANAGER
tristate "Battery charger manager for multiple chargers"
depends on REGULATOR
select EXTCON
help
Say Y to enable charger-manager support, which allows multiple
chargers attached to a battery and multiple batteries attached to a
system. The charger-manager also can monitor charging status in
runtime and in suspend-to-RAM by waking up the system periodically
with help of suspend_again support.
config CHARGER_LT3651
tristate "Analog Devices LT3651 charger"
depends on GPIOLIB
help
Say Y to include support for the Analog Devices (Linear Technology)
LT3651 battery charger which reports its status via GPIO lines.
config CHARGER_LTC4162L
tristate "LTC4162-L charger"
depends on I2C
select REGMAP_I2C
help
Say Y to include support for the Analog Devices (Linear Technology)
LTC4162-L battery charger connected to I2C.
config CHARGER_MAX14577
tristate "Maxim MAX14577/77836 battery charger driver"
depends on MFD_MAX14577
help
Say Y to enable support for the battery charger control sysfs and
platform data of MAX14577/77836 MUICs.
config CHARGER_DETECTOR_MAX14656
tristate "Maxim MAX14656 USB charger detector"
depends on I2C
depends on OF
help
Say Y to enable support for the Maxim MAX14656 USB charger detector.
The device is compliant with the USB Battery Charging Specification
Revision 1.2 and can be found e.g. in Kindle 4/5th generation
readers and certain LG devices.
config CHARGER_MAX77650
tristate "Maxim MAX77650 battery charger driver"
depends on MFD_MAX77650
help
Say Y to enable support for the battery charger control of MAX77650
PMICs.
config CHARGER_MAX77693
tristate "Maxim MAX77693 battery charger driver"
depends on MFD_MAX77693
help
Say Y to enable support for the Maxim MAX77693 battery charger.
config CHARGER_MAX77705
tristate "Maxim MAX77705 battery charger driver"
depends on MFD_MAX77705
help
Say Y to enable support for the Maxim MAX77705 battery charger.
config CHARGER_MAX77759
tristate "Maxim MAX77759 battery charger driver"
depends on MFD_MAX77759 && REGULATOR
default MFD_MAX77759
help
Say M or Y here to enable the MAX77759 battery charger. MAX77759
charger is a function of the MAX77759 PMIC. This is a dual input
switch-mode charger. This driver supports buck and OTG boost modes.
If built as a module, it will be called max77759_charger.
config CHARGER_MAX77976
tristate "Maxim MAX77976 battery charger driver"
depends on I2C
select REGMAP_I2C
help
The Maxim MAX77976 is a 19 Vin, 5.5A 1-Cell Li+ Battery Charger
USB OTG support. It has an I2C interface for configuration.
Say Y to enable support for the Maxim MAX77976 battery charger.
This driver can also be built as a module. If so, the module will be
called max77976_charger.
config CHARGER_MAX8971
tristate "Maxim MAX8971 battery charger driver"
depends on I2C
depends on EXTCON || !EXTCON
select REGMAP_I2C
help
The MAX8971 is a compact, high-frequency, high-efficiency switch-mode
charger for a one-cell lithium-ion (Li+) battery. It delivers up to
1.55A of current to the battery from inputs up to 7.5V and withstands
transient inputs up to 22V.
Say Y to enable support for the Maxim MAX8971 battery charger.
This driver can also be built as a module. If so, the module will be
called max8971_charger.
config CHARGER_MAX8997
tristate "Maxim MAX8997/MAX8966 PMIC battery charger driver"
depends on MFD_MAX8997 && REGULATOR_MAX8997
depends on EXTCON || !EXTCON
help
Say Y to enable support for the battery charger control sysfs and
platform data of MAX8997/LP3974 PMICs.
config CHARGER_MAX8998
tristate "Maxim MAX8998/LP3974 PMIC battery charger driver"
depends on MFD_MAX8998 && REGULATOR_MAX8998
help
Say Y to enable support for the battery charger control sysfs and
platform data of MAX8998/LP3974 PMICs.
config CHARGER_MP2629
tristate "Monolithic power system MP2629 Battery charger"
depends on MFD_MP2629
depends on MP2629_ADC
depends on IIO
help
Select this option to enable support for Monolithic power system
Battery charger. This driver provides Battery charger power management
functions on the systems.
config CHARGER_MT6360
tristate "Mediatek MT6360 Charger Driver"
depends on MFD_MT6360
depends on REGULATOR
select LINEAR_RANGES
help
Say Y here to enable MT6360 Charger Part.
The device supports High-Accuracy Voltage/Current Regulation,
Average Input Current Regulation, Battery Temperature Sensing,
Over-Temperature Protection, DPDM Detection for BC1.2.
config CHARGER_MT6370
tristate "MediaTek MT6370 Charger Driver"
depends on MFD_MT6370
depends on REGULATOR
depends on IIO
select LINEAR_RANGES
help
Say Y here to enable MT6370 Charger Part.
The device supports High-Accuracy Voltage/Current Regulation,
Average Input Current Regulation, Battery Temperature Sensing,
Over-Temperature Protection, DPDM Detection for BC1.2.
This driver can also be built as a module. If so, the module
will be called "mt6370-charger".
config CHARGER_QCOM_SMBB
tristate "Qualcomm Switch-Mode Battery Charger and Boost"
depends on MFD_SPMI_PMIC || COMPILE_TEST
depends on OF
depends on EXTCON
depends on REGULATOR
help
Say Y to include support for the Switch-Mode Battery Charger and
Boost (SMBB) hardware found in Qualcomm PM8941 PMICs. The charger
is an integrated, single-cell lithium-ion battery charger. DT
configuration is required for loading, see the devicetree
documentation for more detail. The base name for this driver is
'pm8941_charger'.
config BATTERY_PM8916_BMS_VM
tristate "Qualcomm PM8916 BMS-VM support"
depends on MFD_SPMI_PMIC || COMPILE_TEST
help
Say Y to add support for Voltage Mode BMS block found in some
Qualcomm PMICs such as PM8916. This hardware block provides
battery voltage monitoring for the system.
To compile this driver as module, choose M here: the
module will be called pm8916_bms_vm.
config CHARGER_PM8916_LBC
tristate "Qualcomm PM8916 Linear Battery Charger support"
depends on MFD_SPMI_PMIC || COMPILE_TEST
depends on EXTCON || !EXTCON
help
Say Y here to add support for Linear Battery Charger block
found in some Qualcomm PMICs such as PM8916. This hardware
blokc provides simple CC/CV battery charger.
To compile this driver as module, choose M here: the
module will be called pm8916_lbc.
config CHARGER_BQ2415X
tristate "TI BQ2415x battery charger driver"
depends on I2C
help
Say Y to enable support for the TI BQ2415x battery charger
PMICs.
You'll need this driver to charge batteries on e.g. Nokia
RX-51/N900.
config CHARGER_BQ24190
tristate "TI BQ24190 battery charger driver"
depends on I2C
depends on EXTCON
depends on GPIOLIB || COMPILE_TEST
help
Say Y to enable support for the TI BQ24190 battery charger.
config CHARGER_BQ24257
tristate "TI BQ24250/24251/24257 battery charger driver"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
select REGMAP_I2C
help
Say Y to enable support for the TI BQ24250, BQ24251, and BQ24257 battery
chargers.
config CHARGER_BQ24735
tristate "TI BQ24735 battery charger support"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
help
Say Y to enable support for the TI BQ24735 battery charger.
config CHARGER_BQ2515X
tristate "TI BQ2515X battery charger family"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
select REGMAP_I2C
help
Say Y to enable support for the TI BQ2515X family of battery
charging integrated circuits. The BQ2515X are highly integrated
battery charge management ICs that integrate the most common
functions for wearable devices, namely a charger, an output voltage
rail, ADC for battery and system monitoring, and push-button
controller.
config CHARGER_BQ257XX
tristate "TI BQ257XX battery charger family"
depends on MFD_BQ257XX
help
Say Y to enable support for the TI BQ257XX family of battery
charging integrated circuits.
config CHARGER_BQ25890
tristate "TI BQ25890 battery charger driver"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
select REGMAP_I2C
help
Say Y to enable support for the TI BQ25890 battery charger.
config CHARGER_BQ25980
tristate "TI BQ25980 battery charger driver"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
select REGMAP_I2C
help
Say Y to enable support for the TI BQ25980, BQ25975 and BQ25960
series of fast battery chargers.
config CHARGER_BQ25630
tristate "TI BQ25630 battery charger driver"
depends on I2C
select REGMAP_I2C
help
Say Y to enable support for the TI BQ25630 battery charger.
config CHARGER_BQ256XX
tristate "TI BQ256XX battery charger driver"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
select REGMAP_I2C
help
Say Y to enable support for the TI BQ256XX battery chargers. The
BQ256XX family of devices are highly-integrated, switch-mode battery
charge management and system power path management devices for single
cell Li-ion and Li-polymer batteries.
config CHARGER_RK817
tristate "Rockchip RK817 PMIC Battery Charger"
depends on MFD_RK8XX
help
Say Y to include support for Rockchip RK817 Battery Charger.
config CHARGER_S2M
tristate "Samsung S2M series PMIC battery charger support"
depends on EXTCON_S2M
depends on MFD_SEC_CORE
help
This option enables support for charger devices found in
certain Samsung S2M series PMICs, such as the S2MU005. These
devices provide USB power supply information and also required
for USB OTG role switching.
config CHARGER_SGM41542
tristate "SGM41542 charger driver"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
depends on REGULATOR
select REGMAP_I2C
help
Say Y to enable support for the SGM41542 battery charger.
config CHARGER_SMB347
tristate "Summit Microelectronics SMB3XX Battery Charger"
depends on I2C
depends on REGULATOR
select REGMAP_I2C
help
Say Y to include support for Summit Microelectronics SMB345,
SMB347 or SMB358 Battery Charger.
config CHARGER_TPS65090
tristate "TPS65090 battery charger driver"
depends on MFD_TPS65090
help
Say Y here to enable support for battery charging with TPS65090
PMIC chips.
config CHARGER_TPS65217
tristate "TPS65217 battery charger driver"
depends on MFD_TPS65217
help
Say Y here to enable support for battery charging with TPS65217
PMIC chips.
config BATTERY_GAUGE_LTC2941
tristate "LTC2941/LTC2943 Battery Gauge Driver"
depends on I2C
help
Say Y here to include support for LTC2941 and LTC2943 Battery
Gauge IC. The driver reports the charge count continuously, and
measures the voltage and temperature every 10 seconds.
config AB8500_BM
bool "AB8500 Battery Management Driver"
depends on AB8500_CORE && AB8500_GPADC && (IIO = y) && OF
select THERMAL
select THERMAL_OF
help
Say Y to include support for AB8500 battery management.
config BATTERY_GOLDFISH
tristate "Goldfish battery driver"
depends on HAS_IOMEM
help
Say Y to enable support for the Goldfish battery and AC power
driver. Originated in the Android Studio Emulator (goldfish) it is
going to be used in other emulators.
config BATTERY_RT5033
tristate "RT5033 fuel gauge support"
depends on I2C
select REGMAP_I2C
help
This adds support for battery fuel gauge in Richtek RT5033 PMIC.
The fuelgauge calculates and determines the battery state of charge
according to battery open circuit voltage.
config CHARGER_RT5033
tristate "RT5033 battery charger support"
depends on MFD_RT5033
depends on EXTCON || !EXTCON
help
This adds support for battery charger in Richtek RT5033 PMIC.
The device supports pre-charge mode, fast charge mode and
constant voltage mode.
config CHARGER_RT9455
tristate "Richtek RT9455 battery charger driver"
depends on I2C
depends on GPIOLIB || COMPILE_TEST
select REGMAP_I2C
help
Say Y to enable support for Richtek RT9455 battery charger.
config CHARGER_RT9467
tristate "Richtek RT9467 Battery Charger Driver"
depends on I2C && GPIOLIB && REGULATOR
select REGMAP_I2C
select REGMAP_IRQ
select LINEAR_RANGES
help
Say Y here to enable RT9467 Battery Charger.
RT9467 is a switch-mode single cell Li-Ion/Li-Polymer battery charger
for portable applications. It integrates a synchronous PWM controller,
power MOSFETs, input current sensing and regulation, high-accuracy
voltage regulation, and charge termination. The charge current is
regulated through integrated sensing resistors. It also features
USB On-The-Go (OTG) support and integrates D+/D- pin for USB
host/charging port detection.
This driver can also be built as a module. If so, the module
will be called "rt9467-charger".
config CHARGER_RT9471
tristate "Richtek RT9471 battery charger driver"
depends on I2C && GPIOLIB && REGULATOR
select REGMAP_I2C
select REGMAP_IRQ
select LINEAR_RANGES
help
This adds support for Richtek RT9471 battery charger. RT9471 is
highly-integrated switch mode battery charger which is system power
patch manageable device for single cell Li-Ion and Li-polymer battery.
It can support BC12 detection on DPDM, and current and voltage
regulation on both charging and boost mode.
This driver can also be built as a module. If so, the module will be
called rt9471.
config CHARGER_RT9756
tristate "Richtek RT9756 smart cap divider charger driver"
depends on I2C
select REGMAP_I2C
select LINEAR_RANGES
help
This adds support for Richtek RT9756 smart cap divider charger driver.
It's a high efficiency and high charge current charger. the device
integrates smart cap divider topology with 9-channel high speed
ADCs that can provide input and output voltage, current and
temperature monitoring.
This driver can also be built as a module. If so, the module will be
called rt9756.
config CHARGER_CROS_USBPD
tristate "ChromeOS EC based USBPD charger"
depends on CROS_USBPD_NOTIFY
help
Say Y here to enable ChromeOS EC based USBPD charger
driver. This driver gets various bits of information about
what is connected to USB PD ports from the EC and converts
that into power_supply properties.
config CHARGER_CROS_PCHG
tristate "ChromeOS EC based peripheral charger"
depends on MFD_CROS_EC_DEV
default MFD_CROS_EC_DEV
help
Say Y here to enable ChromeOS EC based peripheral charge driver.
This driver gets various information about the devices connected to
the peripheral charge ports from the EC and converts that into
power_supply properties.
config CHARGER_CROS_CONTROL
tristate "ChromeOS EC based charge control"
depends on MFD_CROS_EC_DEV
depends on ACPI_BATTERY
default MFD_CROS_EC_DEV
help
Say Y here to enable ChromeOS EC based battery charge control.
This driver can manage charge thresholds and behaviour.
This driver can also be built as a module. If so, the module will be
called cros_charge-control.
config CHARGER_SC2731
tristate "Spreadtrum SC2731 charger driver"
depends on MFD_SC27XX_PMIC || COMPILE_TEST
help
Say Y here to enable support for battery charging with SC2731
PMIC chips.
config FUEL_GAUGE_SC27XX
tristate "Spreadtrum SC27XX fuel gauge driver"
depends on MFD_SC27XX_PMIC || COMPILE_TEST
depends on IIO
help
Say Y here to enable support for fuel gauge with SC27XX
PMIC chips.
config FUEL_GAUGE_STC3117
tristate "STMicroelectronics STC3117 fuel gauge driver"
depends on CRC8
depends on I2C
select REGMAP_I2C
help
Say Y here to enable support for fuel gauge with STC3117
chip.
config CHARGER_UCS1002
tristate "Microchip UCS1002 USB Port Power Controller"
depends on I2C
depends on OF
depends on REGULATOR
select REGMAP_I2C
help
Say Y to enable support for Microchip UCS1002 Programmable
USB Port Power Controller with Charger Emulation.
config CHARGER_BD71828
tristate "Power-supply driver for ROHM BD71828 and BD71815 PMIC"
depends on MFD_ROHM_BD71828
help
Say Y here to enable support for charger and battery
in ROHM BD71815, BD71817, ROHM BD71828 power management
ICs. This driver gets various bits of information about battery
and charger states.
config CHARGER_BD99954
tristate "ROHM bd99954 charger driver"
depends on I2C
select LINEAR_RANGES
help
Say Y here to enable support for getting battery and charger
information and altering charger configurations from the ROHM
BD99954 charger IC.
config CHARGER_WILCO
tristate "Wilco EC based charger for ChromeOS"
depends on WILCO_EC
help
Say Y here to enable control of the charging routines performed
by the Embedded Controller on the Chromebook named Wilco. Further
information can be found in
Documentation/ABI/testing/sysfs-class-power-wilco
config RN5T618_POWER
tristate "RN5T618 charger/fuel gauge support"
depends on MFD_RN5T618
depends on RN5T618_ADC
depends on IIO
help
Say Y here to have support for RN5T618 PMIC family fuel gauge and charger.
This driver can also be built as a module. If so, the module will be
called rn5t618_power.
config BATTERY_ACER_A500
tristate "Acer Iconia Tab A500 battery driver"
depends on MFD_ACER_A500_EC
help
Say Y to include support for Acer Iconia Tab A500 battery fuel gauge.
config BATTERY_SURFACE
tristate "Battery driver for 7th-generation Microsoft Surface devices"
depends on SURFACE_AGGREGATOR_REGISTRY
help
Driver for battery devices connected via/managed by the Surface System
Aggregator Module (SSAM).
This driver provides battery-information and -status support for
Surface devices where said data is not exposed via the standard ACPI
devices. On those models (7th-generation), battery-information is
instead handled directly via SSAM client devices and this driver.
Say M or Y here to include battery status support for 7th-generation
Microsoft Surface devices, i.e. Surface Pro 7, Surface Laptop 3,
Surface Book 3, and Surface Laptop Go.
config CHARGER_SURFACE
tristate "AC driver for 7th-generation Microsoft Surface devices"
depends on SURFACE_AGGREGATOR_REGISTRY
help
Driver for AC devices connected via/managed by the Surface System
Aggregator Module (SSAM).
This driver provides AC-information and -status support for Surface
devices where said data is not exposed via the standard ACPI devices.
On those models (7th-generation), AC-information is instead handled
directly via a SSAM client device and this driver.
Say M or Y here to include AC status support for 7th-generation
Microsoft Surface devices, i.e. Surface Pro 7, Surface Laptop 3,
Surface Book 3, and Surface Laptop Go.
config BATTERY_UG3105
tristate "uPI uG3105 battery monitor driver"
depends on I2C
select ADC_BATTERY_HELPER
help
Battery monitor driver for the uPI uG3105 battery monitor.
Note the uG3105 is not a full-featured autonomous fuel-gauge. Instead
it is expected to be use in combination with some always on
microcontroller reading its coulomb-counter before it can wrap
(it must be read every 400 seconds!).
Since Linux does not monitor coulomb-counter changes while the
device is off or suspended, the functionality of this driver is
limited to reporting capacity only.
config BATTERY_CHARGER_SURFACE_RT
tristate "Battery & Charger driver for Microsoft Surface RT"
depends on I2C && GPIOLIB
help
UEFI/APX driver for the 1st-generation Microsoft Surface RT
battery. Driver supports reading battery properties and
charger status.
This driver can also be built as a module. If so, the module
will be called surface-rt-ec.
config CHARGER_QCOM_SMB2
tristate "Qualcomm PMI8998 PMIC charger driver"
depends on MFD_SPMI_PMIC
depends on IIO
help
Say Y here to enable the Qualcomm PMIC Charger driver. This
adds support for the SMB2 switch mode battery charger found
in PMI8998 and related PMICs.
config FUEL_GAUGE_MM8013
tristate "Mitsumi MM8013 fuel gauge driver"
depends on I2C
select REGMAP_I2C
help
Say Y here to enable the Mitsumi MM8013 fuel gauge driver.
It enables the monitoring of many battery parameters, including
the state of charge, temperature, cycle count, actual and design
capacity, etc.
config MACSMC_POWER
tristate "Apple SMC Battery and Power Driver"
depends on MFD_MACSMC
help
This driver provides support for the battery and AC adapter on
Apple Silicon machines. It exposes battery telemetry (voltage,
current, health) and AC adapter status through the standard Linux
power supply framework.
Say Y or M here if you have an Apple Silicon based Mac.
endif # POWER_SUPPLY
